Updating your node's IPv4 and domain name

All Node Providers are requested to deploy at least one node in their data center with IPv4.

Node Providers are able to add, update, or remove a node’s IPv4 and domain name configuration in one of two ways:

• Method #1: dfx commands (no redeployment required)
  • This method is designed for nodes that onboarded without using a Nitrokey HSM.
• Method #2: IC-OS installation image configuration (redeployment required)
  • This method is designed for nodes that onboarded using a Nitrokey HSM.

Requirements

• IPv4 address
• Domain Name

Method #1: Configure IPv4 via dfx (no redeployment required)

1. Obtain your node operator identity:

   $ dfx identity import node_operator node_operator_private_key.pem --storage-mode=plaintext
   

2. Set IPv4 variables:

   $ NODE_ID="xxxxx-xxxxx-xxxxx-xxxxx-xxxxx-xxxxx-xxxxx-xxxxx-xxxxx-xxxxx-xxx"
   # example: NODE_ID="pqjny-likm7-sjqik-x5m6r-doehn-djdf4-siihl-pnloo-gh3tb-ox6dy-dae"
   
   $ IPV4_PREFIX_LENGTH="xx"
   # example: IPV4_PREFIX_LENGTH="24"
   
   $ IPV4_ADDRESS="xxx.xxx.xxx.xxx"
   # example: IPV4_ADDRESS="12.15.1.89"
   
   $ IPV4_GATEWAY="gateway_ip"
   # example: IPV4_GATEWAY="12.15.1.1"
   
   $ DOMAIN="xxx.xxx.xxx"
   # example: DOMAIN="node1.example.com"
   

3. Submit IPv4 dfx commands to add/update IPv4 configuration and domain name:

   // to add/update your IPv4 configuration:
   $ dfx canister --network ic --identity node_operator call rwlgt-iiaaa-aaaaa-aaaaa-cai update_node_ipv4_config_directly "(record { ipv4_config = opt record { gateway_ip_addr = vec {\"$IPV4_GATEWAY\"}; prefix_length = $IPV4_PREFIX_LENGTH : nat32; ip_addr = \"$IPV4_ADDRESS\"}; node_id = principal \"$NODE_ID\" })"
   
   
   //  to add/update your domain name:
   $ dfx canister --network ic --identity node_operator call rwlgt-iiaaa-aaaaa-aaaaa-cai update_node_domain_directly '(record { node_id = principal \"$NODE_ID\"; domain = opt \"$DOMAIN\" })'
   

   1. Dfx command to remove your node’s IPv4 configuration and domain name:

      // to remove your IPv4 configuration:
      $ dfx canister --network ic --identity node_operator call rwlgt-iiaaa-aaaaa-aaaaa-cai update_node_ipv4_config_directly '(record { ipv4_config = null; node_id = principal \"$NODE_ID\" })'
      
      // to remove your domain name:
      $ dfx canister --network ic --identity node_operator call rwlgt-iiaaa-aaaaa-aaaaa-cai update_node_domain_directly '(record { node_id = principal \"$NODE_ID\"; domain = null })'
      

Method #2: Configure IPv4 via IC-OS Installation (redeployment required)

To redeploy a node with IPv4 and domain name configuration, follow the node deployment guide of your choice, making sure to add the IPv4 and domain name configuration in step 6:

• Legacy (Gen-1) Node Deployment Guide (with an HSM)
• Current (Gen-2) Node Deployment Guide (without an HSM)

Please note that you must reconfigure the IC-OS installation image for every IPv4 node you deploy. This means that you cannot use a single IC-OS installation image to deploy multiple nodes like you are able to do when just configuring IPv6 nodes. After each IPv4 node deployment, you must plug your IC-OS Installation USB stick back into your laptop and return to step 6 in the node deployment guide to reconfigure your installation image.