Difference between revisions of "RMU build Gen-1.5: II. Proxmox - A. Install Proxmox"
From Internet Computer Wiki
Katie.peters (talk | contribs) (Creating the page) |
Katie.peters (talk | contribs) (Working on the page) |
||
Line 8: | Line 8: | ||
#Ensure the RMU is powered off | #Ensure the RMU is powered off | ||
#Plug the USB into the RMU | #Plug the USB into the RMU | ||
− | #Start the server and press the F11 key repeatedly to reach the Boot Menu. | + | #Start the server and press the F11 key repeatedly to reach the Boot Menu. <br />[[File:01 - BIOS Boot Screen.jpg|800x800px]] |
− | #Select the Flash Drive and press enter (screen may differ) | + | #Select the Flash Drive and press enter (screen may differ) <br />[[File:02 - Select USB Boot Media.jpg]] |
− | #Select <code>Install Proxmox VE (Terminal UI)</code> and press enter | + | #Select <code>Install Proxmox VE (Terminal UI)</code> and press enter <br />[[File:IKVM capture (31).jpg|800x800px]] |
− | #Select <code>I agree</code> and press enter | + | #Select <code>I agree</code> and press enter <br />[[File:04 - EULA.jpg|800x800px]] |
− | #Select <code>Advanced options</code> and press enter | + | #Select <code>Advanced options</code> and press enter <br />[[File:05 - Install Boot Disk.jpg|800x800px]] |
#Select <code>ext4</code> and press enter to change this setting | #Select <code>ext4</code> and press enter to change this setting | ||
− | #*Note: For SuperMicros with two internal drives , select <code>ZFS (RAID 1)</code> for SuperMicros with one drive select <code>ZFS (RAID 0)</code> [[File:06 - Install Boot Disk - Select ZFS (RAID1).jpg|800x800px]] | + | #*Note: For SuperMicros with two internal drives , select <code>ZFS (RAID 1)</code> for SuperMicros with one drive select <code>ZFS (RAID 0)</code> <br />[[File:06 - Install Boot Disk - Select ZFS (RAID1).jpg|800x800px]] |
− | #Select <code>Ok</code> and press enter | + | #Select <code>Ok</code> and press enter <br />[[File:07 - Install Boot Disk - Accept ZFS.jpg|800x800px]] |
− | #Select <code>Next</code> and press enter | + | #Select <code>Next</code> and press enter [[File:08 - Start Installer.jpg|800x800px]] |
− | #Select your Country, Timezone (Recommended UTC), and Keyboard layout | + | #Select your Country, Timezone (Recommended UTC), and Keyboard layout <br />[[File:09 - Select Country.jpg|800x800px]] [[File:10 - Select System Timezone.jpg|800x800px]] [[File:11 - Select Keyboard Type.jpg|800x800px]] |
− | #Select <code>Next</code> and press enter | + | #Select <code>Next</code> and press enter <br />[[File:12 - Continue Installer.jpg|800x800px]] |
#Enter in a password, please make this a strong password, and store it in your password manager | #Enter in a password, please make this a strong password, and store it in your password manager | ||
#Enter in an email to receive alerts | #Enter in an email to receive alerts | ||
− | #Select <code>Next</code> and press enter | + | #Select <code>Next</code> and press enter <br />[[File:13 - Set Root Password and Email.jpg|800x800px]] |
#These instructions assume that you followed the RMU Cabling instructions earlier in the document | #These instructions assume that you followed the RMU Cabling instructions earlier in the document | ||
#Select the <code>Management Interface</code> and change it to <code>eno1</code> and press enter | #Select the <code>Management Interface</code> and change it to <code>eno1</code> and press enter | ||
− | #For <code>Hostname (FQDN):</code> input*<code><dc>-rmu.<domain></code> (if supporting multiple sites).* This will be the fully qualified domain name (FQDN) name for the RMU itself as added to the DNS in the Prerequisites section. | + | #For <code>Hostname (FQDN):</code> input*<code><dc>-rmu.<domain></code> (if supporting multiple sites).* This will be the fully qualified domain name (FQDN) name for the RMU itself as added to the DNS in the Prerequisites section. For the <code>External IP</code> and network mask determined in the Prerequisites section. |
#For <code>IP address (CIDR):</code> enter the <code>External IP</code> and <code>Netmask</code> determined in the Prerequisites section | #For <code>IP address (CIDR):</code> enter the <code>External IP</code> and <code>Netmask</code> determined in the Prerequisites section | ||
#For <code>Gateway address:</code> enter in your public <code>Gateway</code> determined in the Prerequisites section | #For <code>Gateway address:</code> enter in your public <code>Gateway</code> determined in the Prerequisites section | ||
− | #For <code>DNS Server</code> address: enter in <code>1.1.1.1</code> | + | #For <code>DNS Server</code> address: enter in <code>1.1.1.1</code><br />[[File:IKVM capture (29).jpg|800x800px]] |
− | #Select <code>Next</code> and press enter | + | #Select <code>Next</code> and press enter <br />[[File:IKVM capture (28).jpg|800x800px]] |
#Look over to ensure all information is correct | #Look over to ensure all information is correct | ||
− | + | #Select <code>Install</code> and press enter. Make sure it is checked to reboot after installation | |
− | ##You should now see the login screen. If need be you can login as root and the password you set earlier | + | #*If you set the boot order to boot off of the USB, then remove it before the reboot <br />[[File:IKVM capture (30).jpg|800x800px]] |
− | + | #You should now see the login screen. If need be, you can login as root and use the password you set earlier | |
+ | #Take note of the IP address and port shown on this screen <br />[[File:17 - Console Login.jpg|800x800px]] |
Revision as of 19:49, 22 February 2024
This page is part of the Gen-1.5 RMU build runbook.
Go back to the previous section: Prerequisites
Install Proxmox
- Insert your Proxmox USB drive that you made earlier into the RMU
- Ensure the RMU is powered off
- Plug the USB into the RMU
- Start the server and press the F11 key repeatedly to reach the Boot Menu.
- Select the Flash Drive and press enter (screen may differ)
- Select
Install Proxmox VE (Terminal UI)
and press enter - Select
I agree
and press enter - Select
Advanced options
and press enter - Select
ext4
and press enter to change this setting - Select
Ok
and press enter - Select
Next
and press enter - Select your Country, Timezone (Recommended UTC), and Keyboard layout
- Select
Next
and press enter - Enter in a password, please make this a strong password, and store it in your password manager
- Enter in an email to receive alerts
- Select
Next
and press enter - These instructions assume that you followed the RMU Cabling instructions earlier in the document
- Select the
Management Interface
and change it toeno1
and press enter - For
Hostname (FQDN):
input*<dc>-rmu.<domain>
(if supporting multiple sites).* This will be the fully qualified domain name (FQDN) name for the RMU itself as added to the DNS in the Prerequisites section. For theExternal IP
and network mask determined in the Prerequisites section. - For
IP address (CIDR):
enter theExternal IP
andNetmask
determined in the Prerequisites section - For
Gateway address:
enter in your publicGateway
determined in the Prerequisites section - For
DNS Server
address: enter in1.1.1.1
- Select
Next
and press enter - Look over to ensure all information is correct
- Select
Install
and press enter. Make sure it is checked to reboot after installation - You should now see the login screen. If need be, you can login as root and use the password you set earlier
- Take note of the IP address and port shown on this screen